Sculpting tools

1 of 10
DICTUM Carving Tool, Flat/Skew, Double Bevel 2/6 mm

DICTUM Carving Tool, Flat/Skew, Double Bevel

Straight chisels are preferred for lettering, but are also suitable for chip carving and for smoothing straight or slightly convex surfaces in figure sculpting. The skewed variant can be drawn across the surface and cuts into corners...
variants
   
€29.40

incl. VAT plus shipping costs

Article No. 701524

DICTUM Carving Tools, 12-Piece Set

DICTUM Carving Tools, 12-Piece Set

With these twelve sculptor's tools you are perfectly equipped for sculpting figures and ornaments. Flat 10 mm; flat/skew 10 mm; V-parting tool 41 V 65° / 6 mm; gouges, straight sweep 6 / 10 and 20 mm; sweep 8 / 6 and 13 mm; sweep 9 / 6...
   
€424.00

incl. VAT plus shipping costs

Article No. 701481

DICTUM Carving Tool, Pod Tool 64/6 mm

DICTUM Carving Tool, Pod Tool

Thanks to their conical form, pod tools are used for backcutting in relief carving and for general finishing work. Their projecting corners make it easy to cut within narrow recesses, in which the angle of the gouge can still be corrected.
variants
   
€31.70

incl. VAT plus shipping costs

Article No. 701499

DICTUM Carving Tool, Pod Tool 66/6 mm

DICTUM Carving Tool, Pod Tool

Thanks to their conical form, pod tools are used for backcutting in relief carving and for general finishing work. Their projecting corners make it easy to cut within narrow recesses, in which the angle of the gouge can still be corrected.
variants
   
€31.60

incl. VAT plus shipping costs

Article No. 701506

DICTUM Carving Tool, Pod Tool 70/6 mm

DICTUM Carving Tool, Pod Tool

Thanks to their conical form, pod tools are used for backcutting in relief carving and for general finishing work. Their projecting corners make it easy to cut within narrow recesses, in which the angle of the gouge can still be corrected.
variants
   
€34.10

incl. VAT plus shipping costs

Article No. 701508

DICTUM Carving Tool, Dogleg Gouge 82/6 mm

DICTUM Carving Tool, Dogleg Gouge 82/6 mm

This gouge is used to clear the ground of deep, shouldered areas to their final depth and to rework corners.
   
€50.70

incl. VAT plus shipping costs

Article No. 701529

DICTUM Carving Tool, Gouge, Back Bent, Inside Bevel 34/6 mm

DICTUM Carving Tools, Gouges, Back Bent, Inside Bevel

Primarily used for convex shapes and cylindrical profiles which cannot be worked on with a turned straight gouge because of the strong curve.
variants
   
€36.30

incl. VAT plus shipping costs

Article No. 701477

DICTUM Carving Tool, Gouge/V-Parting Tool, Short Bent 29/10 mm

DICTUM Carving Tools, Gouge/V-Parting Tools, Short Bent

Similar to the long bent form, these gouges are also used for deep, curved shapes. The even stronger bend of the gouge allows you to carve transitions in even deeper areas and to create small radiuses and arches.
variants
   
€32.70

incl. VAT plus shipping costs

Article No. 701461

DICTUM Carving Tool, Gouge/V-Parting Tool, Short Bent 30/10 mm

DICTUM Carving Tools, Gouge/V-Parting Tools, Short Bent

Similar to the long bent form, these gouges are also used for deep, curved shapes. The even stronger bend of the gouge allows you to carve transitions in even deeper areas and to create small radiuses and arches.
variants
   
€32.70

incl. VAT plus shipping costs

Article No. 701463

DICTUM Carving Tool, Gouge/V-Parting Tool, Short Bent 32/6 mm

DICTUM Carving Tools, Gouge/V-Parting Tools, Short Bent

Similar to the long bent form, these gouges are also used for deep, curved shapes. The even stronger bend of the gouge allows you to carve transitions in even deeper areas and to create small radiuses and arches.
variants
   
€33.00

incl. VAT plus shipping costs

Article No. 701749

DICTUM Carving Tool, V-Parting Tool 41 V 65°/3 mm

DICTUM Carving Tools, V-Parting Tools

V-parting tools are popularly used in relief carving to delimit areas. Another important use is the cutting of even grooves.
variants
   
€34.30

incl. VAT plus shipping costs

Article No. 701466

DICTUM Carving Tool, V-Parting Tool 45 V 95°/3 mm

DICTUM Carving Tools, V-Parting Tools

V-parting tools are popularly used in relief carving to delimit areas. Another important use is the cutting of even grooves.
variants
   
€34.70

incl. VAT plus shipping costs

Article No. 701475

DICTUM Carving Tool, Gouge/V-Parting Tool, Long Bent 17/13 mm

DICTUM Carving Tool, Gouge/V-Parting Tool, Long Bent

The long bent form is used in curved recesses to allow you to cut out of the piece from the deepest point without damaging the edges of recess.
variants
   
€35.60

incl. VAT plus shipping costs

Article No. 701456

DICTUM Carving Tool, Gouge/V-Parting Tool, Long Bent 18/10 mm

DICTUM Carving Tool, Gouge/V-Parting Tool, Long Bent

The long bent form is used in curved recesses to allow you to cut out of the piece from the deepest point without damaging the edges of recess.
variants
   
€35.50

incl. VAT plus shipping costs

Article No. 701459

DICTUM Carving Tool, Gouge, Straight 3/6 mm

DICTUM Carving Tools, Gouges, Straight

Gouges are used for anything from rough work to shaping and finishing, and are therefore the most versatile sculptor's tools. If necessary, each of these gouges can also be used the other way round to work on convex surfaces. Sweep 11,...
variants
   
€29.90

incl. VAT plus shipping costs

Article No. 701653

DICTUM Carving Tool, Gouge, Straight 4/6 mm

DICTUM Carving Tools, Gouges, Straight

Gouges are used for anything from rough work to shaping and finishing, and are therefore the most versatile sculptor's tools. If necessary, each of these gouges can also be used the other way round to work on convex surfaces. Sweep 11,...
variants
   
€29.90

incl. VAT plus shipping costs

Article No. 701750

DICTUM Carving Tool, Gouge, Straight 5/20 mm

DICTUM Carving Tools, Gouges, Straight

Gouges are used for anything from rough work to shaping and finishing, and are therefore the most versatile sculptor's tools. If necessary, each of these gouges can also be used the other way round to work on convex surfaces. Sweep 11,...
variants
   
€36.10

incl. VAT plus shipping costs

Article No. 701429

DICTUM CarvingTool, Gouge, Straight 6/6 mm

DICTUM Carving Tools, Gouges, Straight

Gouges are used for anything from rough work to shaping and finishing, and are therefore the most versatile sculptor's tools. If necessary, each of these gouges can also be used the other way round to work on convex surfaces. Sweep 11,...
variants
   
€31.70

incl. VAT plus shipping costs

Article No. 701751

DICTUM Carving Tool, Gouge, Straight 7/20 mm

DICTUM Carving Tools, Gouges, Straight

Gouges are used for anything from rough work to shaping and finishing, and are therefore the most versatile sculptor's tools. If necessary, each of these gouges can also be used the other way round to work on convex surfaces. Sweep 11,...
variants
   
€40.30

incl. VAT plus shipping costs

Article No. 701436

DICTUM Carving Tool, Gouge, Straight 8/6 mm

DICTUM Carving Tools, Gouges, Straight

Gouges are used for anything from rough work to shaping and finishing, and are therefore the most versatile sculptor's tools. If necessary, each of these gouges can also be used the other way round to work on convex surfaces. Sweep 11,...
variants
   
€31.70

incl. VAT plus shipping costs

Article No. 701654

DICTUM Carving Tool, Gouge, Straight 9/6 mm

DICTUM Carving Tools, Gouges, Straight

Gouges are used for anything from rough work to shaping and finishing, and are therefore the most versatile sculptor's tools. If necessary, each of these gouges can also be used the other way round to work on convex surfaces. Sweep 11,...
variants
   
€32.10

incl. VAT plus shipping costs

Article No. 701669

DICTUM Carving Tool, Gouge, Straight 10/6 mm

DICTUM Carving Tools, Gouges, Straight

Gouges are used for anything from rough work to shaping and finishing, and are therefore the most versatile sculptor's tools. If necessary, each of these gouges can also be used the other way round to work on convex surfaces. Sweep 11,...
variants
   
€32.30

incl. VAT plus shipping costs

Article No. 701698

DICTUM Carving Tool, Gouge, Straight 11/3 mm

DICTUM Carving Tools, Gouges, Straight

Gouges are used for anything from rough work to shaping and finishing, and are therefore the most versatile sculptor's tools. If necessary, each of these gouges can also be used the other way round to work on convex surfaces. Sweep 11,...
variants
   
€33.90

incl. VAT plus shipping costs

Article No. 701699

DICTUM Carving Tool, Chisel, Double Bevel 1/3 mm

DICTUM Carving Tools, Chisels, Double Bevel

Straight chisels are preferred for lettering, but are also suitable for chip carving and for smoothing straight or slightly convex surfaces in figure sculpting. The skewed variant can be drawn across the surface and cuts into corners...
variants
   
€28.70

incl. VAT plus shipping costs

Article No. 701744

DICTUM Carving Tool, V-Parting Tool, Short Bent 44/3 mm

DICTUM Carving Tool, V-Parting Tool, Short Bent

Similar to the long bent form, these gouges are also used for deep, curved shapes. The even stronger bend of the gouge allows you to carve transitions in even deeper areas and to create small radiuses and arches.
variants
   
€36.80

incl. VAT plus shipping costs

Article No. 701473

DICTUM Carving Tool, V-Parting Tool, Long Bent 42/6 mm

DICTUM Carving Tool, V-Parting Tool, Long Bent 42/6 mm

The long bent form is used in curved recesses to allow you to cut out of the piece from the deepest point without damaging the edges of recess.
   
€39.30

incl. VAT plus shipping costs

Article No. 701472

DICTUM Carving Tools, 6-Piece Set, in Cotton Tool  Roll

DICTUM Carving Tools, 6-Piece Sets

6-piece set as basic equipment for beginners. Flat/skew 13 mm; V-parting tool 41 V 65° / 10 mm; gouges, straight sweep 5 / 20 mm; sweep 6 / 13 mm; sweep 8 / 10 mm; sweep 10 / 6 mm.
variants
   
€191.00

incl. VAT plus shipping costs

Article No. 701536

DICTUM Compact Sculpting Chisel, Sweep 8 / 5 mm

DICTUM Compact Carving Tool

The blade is shorter than standard carving tools to work closer to the workpiece. The sculptor can create extraordinarily precise details by hand thanks to the combination of a short blade with a compact octagonal ball grip that lies...
variants
   
€35.60

incl. VAT plus shipping costs

Article No. 701688

DICTUM Compact Sculpting Chisel, Sweep 7 / 5 mm

DICTUM Compact Carving Tool

The blade is shorter than standard carving tools to work closer to the workpiece. The sculptor can create extraordinarily precise details by hand thanks to the combination of a short blade with a compact octagonal ball grip that lies...
variants
   
€34.30

incl. VAT plus shipping costs

Article No. 701685

DICTUM Compact Sculpting Chisel, Sweep 6 / 16 mm

DICTUM Compact Carving Tool

The blade is shorter than standard carving tools to work closer to the workpiece. The sculptor can create extraordinarily precise details by hand thanks to the combination of a short blade with a compact octagonal ball grip that lies...
variants
   
€39.80

incl. VAT plus shipping costs

Article No. 701682

DICTUM Compact Carving Tool, Sweep 5 / 13 mm

DICTUM Compact Carving Tool

The blade is shorter than standard carving tools to work closer to the workpiece. The sculptor can create extraordinarily precise details by hand thanks to the combination of a short blade with a compact octagonal ball grip that lies...
variants
   
€35.10

incl. VAT plus shipping costs

Article No. 701680

DICTUM Carving Tools in Cotton Tool Roll, 4-Piece Set

DICTUM Carving Tools in Cotton Tool Roll, 4-Piece Set

4-piece set as a basic equipment for beginners. DICTUM carving knife, shape BS/K, with leather cutting edge protection and selected DICTUM carving tools. Flat 1 / 10 mm; V-parting tool 41 V 65° / 10 mm; gouge, straight, sweep 8 / 10 mm.
   
€134.00

incl. VAT plus shipping costs

Article No. 728901

Pfeil Dräyer Gouge, Blade Width 60 mm

Pfeil Dräyer Gouge, Blade Width 60 mm

Ideal for preliminary cutting. Slightly skewed blade for pulling cut and good chip formation. Bevelled on both sides.
 
€92.30

incl. VAT plus shipping costs

Article No. 701279

Pfeil Allongee Gouges, Sweep 2 / 60 mm

Pfeil Allongee Gouges

With its extra-hard white beech handle and heavy-duty ferrule, this gouge is designed for rough shaping with the mallet and can resist even the toughest impact.
variants
 
€93.70

incl. VAT plus shipping costs

Article No. 700946

Pfeil Allongee Gouges, Sweep 3 / 50 mm

Pfeil Allongee Gouges

With its extra-hard white beech handle and heavy-duty ferrule, this gouge is designed for rough shaping with the mallet and can resist even the toughest impact.
variants
 
€85.40

incl. VAT plus shipping costs

Article No. 701274

Pfeil Allongee Gouges, Sweep 5 / 50 mm

Pfeil Allongee Gouges

With its extra-hard white beech handle and heavy-duty ferrule, this gouge is designed for rough shaping with the mallet and can resist even the toughest impact.
variants
 
€85.40

incl. VAT plus shipping costs

Article No. 701275

Pfeil Allongee Gouges, Sweep 7 / 50 mm

Pfeil Allongee Gouges

With its extra-hard white beech handle and heavy-duty ferrule, this gouge is designed for rough shaping with the mallet and can resist even the toughest impact.
variants
 
€91.00

incl. VAT plus shipping costs

Article No. 701276

Pfeil Allongee Gouges, Sweep 8 / 60 mm

Pfeil Allongee Gouges

With its extra-hard white beech handle and heavy-duty ferrule, this gouge is designed for rough shaping with the mallet and can resist even the toughest impact.
variants
 
€103.00

incl. VAT plus shipping costs

Article No. 701271

Pfeil Allongee Gouges, Sweep 9 / 50 mm

Pfeil Allongee Gouges

With its extra-hard white beech handle and heavy-duty ferrule, this gouge is designed for rough shaping with the mallet and can resist even the toughest impact.
variants
 
€104.00

incl. VAT plus shipping costs

Article No. 700949

Pfeil Carving Tool, Gouge, Fishtail, Thin Blades, Sweep 3F / 6 mm

Pfeil Carving Tool, Gouge, Fishtail, Thin Blades

Thanks to their conical form, fishtail gouges are used for backcutting in relief carving and for general finishing work. Their projecting corners make it easy to cut within narrow recesses, in which the angle of the gouge can still be...
variants
 
€33.40

incl. VAT plus shipping costs

Article No. 700740

Pfeil Carving Tool, Gouge, Fishtail, Thin Blades, Sweep 5F / 8 mm

Pfeil Carving Tool, Gouge, Fishtail, Thin Blades

Thanks to their conical form, fishtail gouges are used for backcutting in relief carving and for general finishing work. Their projecting corners make it easy to cut within narrow recesses, in which the angle of the gouge can still be...
variants
 
€33.40

incl. VAT plus shipping costs

Article No. 700745

Pfeil Carving Tool, Gouge, Fishtail, Thin Blades, Sweep 7F / 6 mm

Pfeil Carving Tool, Gouge, Fishtail, Thin Blades

Thanks to their conical form, fishtail gouges are used for backcutting in relief carving and for general finishing work. Their projecting corners make it easy to cut within narrow recesses, in which the angle of the gouge can still be...
variants
 
€33.40

incl. VAT plus shipping costs

Article No. 700750

Pfeil Carving Tool, Gouge, Fishtail, Thin Blades, Sweep 9F / 5 mm

Pfeil Carving Tool, Gouge, Fishtail, Thin Blades

Thanks to their conical form, fishtail gouges are used for backcutting in relief carving and for general finishing work. Their projecting corners make it easy to cut within narrow recesses, in which the angle of the gouge can still be...
variants
 
€33.80

incl. VAT plus shipping costs

Article No. 700755

Pfeil Carving Tool, Dragon Gouge, Bevel Straight

Pfeil Carving Tool, Dragon Gouge, Bevel Straight

This strongly bent gouge is ideal for deep recesses and for finishing corners, lettering and ornaments.
 
€34.90

incl. VAT plus shipping costs

Article No. 700689

Pfeil Carving Tool, Dogleg Gouge, Sweep 21 / 6 mm

Pfeil Carving Tool, Dogleg Gouge

This gouge is used to clear the ground of deep, shouldered areas to their final depth and to rework corners.
variants
 
€34.90

incl. VAT plus shipping costs

Article No. 700728

Pfeil Carving Tool, Gouge, Back Bent, Inside Bevel, Sweep 20 / 10 mm

Pfeil Carving Tools, Gouges, Back Bent, Inside Bevel

Primarily used for convex shapes and cylindrical profiles which cannot be worked on with a turned straight gouge because of the strong curve.
variants
 
€35.90

incl. VAT plus shipping costs

Article No. 701361

Pfeil Carving Tool, Gouge, Back Bent, Inside Bevel, Sweep 25 / 6 mm

Pfeil Carving Tools, Gouges, Back Bent, Inside Bevel

Primarily used for convex shapes and cylindrical profiles which cannot be worked on with a turned straight gouge because of the strong curve.
variants
 
€35.90

incl. VAT plus shipping costs

Article No. 700736

Pfeil Carving Tool, Gouge/V-Parting Tool, Short Bent, Sweep 3A / 12 mm

Pfeil Carving Tools, Gouges/V-Parting Tools, Short Bent

Similar to the long bent form, these gouges are also used for deep, curved shapes. The even stronger bend of the gouge allows you to carve transitions in even deeper areas and to create small radiuses and arches.
variants
 
€30.10

incl. VAT plus shipping costs

Article No. 701257

1 of 10