Prices with or without VAT?
This setting applies to all prices but may be changed at any time.
 

Tormek T-8 incl. Hand Tool Kit HTK-706

Tormek T-8 incl. Hand Tool Kit HTK-706
"Tormek-Original" sharpening stone (SG-250) aluminium oxide Ø 250 x 50 mm, grit 220; leather...
NEW! Maximum precision and solid zinc cast housing
TORMEK T-8 takes precision and stability to a completely new level. The new design integrates the previously mounted sleeves for the vertical and horizontal support into the revolutionary fully cast top and frame. The enhanced stability optimizes jig guidance and thus the sharpening accuracy.
"Tormek-Original" sharpening stone (SG-250) aluminium oxide Ø 250 x 50 mm, grit 220; leather honing wheel Ø 220 x 30 mm; universal support, finely adjustable (can be used horizontally or vertically). Powder coated steel plate housing. 230 V, 200 W, 90 rpm, torque 14.7 Nm, 14.8 kg.
Includes:
  • Hand Tool Kit HTK-706 with short jig, axe jig, knife jig, small knife holder, long knives jig, scissors jig
  • Square edge precision jig (SE-77)
  • Adjustable trueing tool (TT-50)
  • Stone preparer (SP-650)
  • Angle gauge (WM-200)
  • Honing compound (PA-70)
  • Handbook (HB-10)
  • Instruction video (DVD-1)
  • Workshop "Sharpening on the Tormek"
Tormek Sharpening System
Proven for many years and constantly perfected wet-working sharpening machines are the basis of the ingenious Tormek sharpening system. A range of jigs, which can be mounted on the universal support, makes the sharpening of any cutting tool easier. Tormek enables the achievement of exact cutting geometry and consistent results for chisels, turning tools, knives, shears or machine tools. Also suitable for workshops and instructional settings because of safe operation - no sparks are produced and it has an overload safety clutch.
The "Tormek-Original" ceramic wheel assures short sharpening times under all conditions in combination with the greatest possible tool protection. The front end can also be used for plane honing. The leather honing wheel removes burrs quickly and leaves a perfectly polished cutting edge. Robust construction with solid housing and sliding water container.
A summary of the advantages of Tormek sharpening machines
Longer working life of T-8 and T-4:
  • Stainless steel spindle with EzyLock-System for easier stone assembling
  • Solid zinc cast housing with integrated vertical and horizontal support
  • Better motor insulation

Additional advantages of T-8:
  • Electrophoretic dip painted casing, zinc cast housing frame and robust ABS plastic sides for better corrosion protection
  • Silent running, maintenance free motor, designed for continuous operation, 25 000 hour life
  • Improved water container with screw lift for easy positioning, overspill rim, drip-off plate, magnetic swarf collector and magnetic cleaning scraper
  • Two additional rubber feet to drain off water on the case
     
    more
    less
    Hier finden Sie weitere Details zum Hersteller
     
    Discover product in our flip catalogue:
    Discover product in our flip catalogue:
     
     
    Learn the professional use of the Tormek machine. If you buy a Tormek T-4 or T-8 you may take part in a special course "Sharpening with Tormek" free of charge.
     
    Article no. 716055
    Brand Tormek
    Item in stock
    €749.00 per set

    Prices incl. VAT

    i

    plus shipping costs

    Remember
    Many other models
    Type Price Quantity
    Tormek T-8 inkl. Haus- und Heimpaket HTK-706
      €749.00
     

     
     
    Plenty of accessories and spare parts

    Accessories

    Tormek Pro Angle Master WM-200

    Tormek® Pro Angle Master WM-200

    For setting the grinding angle and checking the bevel geometry. Grinding jigs and accessories are suitable for all models (T-3, T-4, T-7 and T-8) unless otherwise noted.
    €19.30

    incl. VAT plus shipping costs

    Article No. 705240

    Tormek Handbook, Grinding and Sharpening Edge Tools (HB 10)

    Tormek® Handbook, Grinding and Sharpening Edge Tools (HB 10)

    By Torgny Jansson. General introduction to the basics of sharpening and detailed instructions for use of the Tormek. (Every machine comes with handbook and DVD).
    €12.30

    incl. VAT plus shipping costs

    Article No. 705199

    Tormek Drill Bit Sharpening Attachment DBS-22

    Tormek® Drill Bit Sharpening Attachment DBS-22

    Sharpening the complex tip geometry of a drill by hand requires plenty of practice. Using the Tormek drill bit sharpener attachment, you can now sharpen a 4-facet drill bit with the usual wet-grinding method on your drill for maximum...
    €189.90

    incl. VAT plus shipping costs

    Article No. 705231

    Tormek Instruction DVD

    Tormek® Instruction DVD

    „Edge-tool sharpening the Tormek way“. (Comes with every machine). 23 min., DVD 2.0, PAL. In German, English, French and Swedish.
    €13.30

    incl. VAT plus shipping costs

    Article No. 705446

    Tormek  Woodturner's Kit TNT-708

    Tormek® Woodturner's Kit TNT-708

    Grinding jig for woodturning gouges, additional addapter for cutters, additional multi-tip adapter, multi jig, tool rest, leather honing wheel, woodturning tool setter, machine dust cover and instruction box for woodturners (in English).
    €239.00

    incl. VAT plus shipping costs

    Article No. 705454

    Tormek Handbook, Nassschleifen und Abziehen von Schneidwerkzeugen (HB 10)

    Tormek® Handbook, Nassschleifen und Abziehen von...

    By Torgny Jansson. General introduction to the basics of sharpening and detailed instructions for use of the Tormek. (Every machine comes with handbook and DVD).
    €23.20

    incl. VAT plus shipping costs

    Article No. 705211

    Tormek Universal Support US-105 for T-7

    Tormek® Universal Support US-105 for T-7

    With fine adjustment suitable for Tormek T-7, T-8 and old series models.
    €34.30

    incl. VAT plus shipping costs

    Article No. 705206

     

    Replacement parts

    DICTUM Japanese Shaping Wheel for Tormek, Grit 80

    DICTUM Japanese Shaping Wheel for Tormek, Grit 80

    Extra-coarse stone with hard bond for repairing damaged tool blades. Primarily suitable for double-layered blades and carbon steel.
    €119.00

    incl. VAT plus shipping costs

    Article No. 716030

    Plastic bearing

    Plastic bearing

    Fits No. 705228 , 705236 and 705247 .
    €2.50

    incl. VAT plus shipping costs

    Article No. 800012

    Tormek Settling Disk

    Tormek Settling Disk

    Suitable for Tormek T-3, T-4, T-7, T-8 and old series models.
    €1.50

    incl. VAT plus shipping costs

    Article No. 800035

    €57.30

    incl. VAT plus shipping costs

    Article No. 705212

    Button Switch for Tormek

    Button Switch for Tormek

    The switch is available in two types - depending on the year the machine was built, as a toggle switch or a button switch. Check whether a toggle switch no. 800046 or a button switch no. 8000504 is installed on your machine. You must...
    €20.20

    incl. VAT plus shipping costs

    Article No. 800504

    Tormek Orginal Replacement Wheel SG-250, Grit 220

    Tormek Orginal Replacement Wheel SG-250, Grit 220

    This hard-bond stone is suitable for pre-sharpening double-layered blades as well as chrome-vanadium steel and HSS.
    €139.00

    incl. VAT plus shipping costs

    Article No. 705201

    Tormek Main Shaft Set MSK-250

    Tormek Main Shaft Set MSK-250

    For easier fitting of the grinding stones the main shaft is now supplied with a left-hand thread. The new EzyLock nut can be tightened by hand and securely clamps the stone. Set consists of main shaft with left-hand thread, EzyLock nut,...
    €39.90

    incl. VAT plus shipping costs

    Article No. 800500

    Tormek Knurled Screw Sharpening Wheel

    Tormek Knurled Screw Sharpening Wheel

    Suitable for Tormek T-7, T-8 and old series models.
    €7.40

    incl. VAT plus shipping costs

    Article No. 800038

    Knurled Nut for Tormek

    Knurled Nut for Tormek

    Fits Tormek T-3, T-4, T-7 and T-8.
    €5.90

    incl. VAT plus shipping costs

    Article No. 800343

    Tormek Eyelet for Cover No. 800040

    Tormek Eyelet for Cover No. 800040

    Suitable for Tormek T-3, T-7 and old series models.
    €3.90

    incl. VAT plus shipping costs

    Article No. 800042

    Tormek Diamond Tip ADV D 50

    Tormek Diamond Tip ADV D 50

    For the diamond stone dresser. Grinding jigs and accessories are suitable for all models (T-3, T-4, T-7 and T-8) unless otherwise noted.
    €35.90

    incl. VAT plus shipping costs

    Article No. 705217

    Tormek Driving Wheel Safety Lock Pin

    Tormek Driving Wheel Safety Lock Pin

    Suitable for Tormek T-3, T-4, T-7, T-8 and old series models.
    €1.50

    incl. VAT plus shipping costs

    Article No. 800037

    Tormek Settling Disk

    Tormek Settling Disk

    Suitable for Tormek T-3, T-4, T-7, T-8 and old series models.
    €2.30

    incl. VAT plus shipping costs

    Article No. 800034

    Tormek Honing Compound PA-70

    Tormek Honing Compound PA-70

    For leather honing wheels No. 705212 and 705197 . 70 g.
    €9.90

    (Content: €14.14 / 100 g)

    incl. VAT plus shipping costs

    Article No. 705213

    Knurled Screw fastening Rest for Tormek

    Knurled Screw fastening Rest for Tormek

    Suitable for Tormek T-3, T-4, T-7, T-8 and old series models.
    €5.20

    incl. VAT plus shipping costs

    Article No. 800041

    Tormek Eyelet M12, H4 at Drive Wheel

    Tormek Eyelet M12, H4 at Drive Wheel

    Suitable for Tormek T-7, T-8 and old series models.
    €4.50

    incl. VAT plus shipping costs

    Article No. 800039

    Tormek Cover

    Tormek Cover

    Suitable for Tormek T-3, T-4, T-7, T-8 and old series models.
    €4.40

    incl. VAT plus shipping costs

    Article No. 800047

    Tormek Drive Wheel with Rubber Band for T-7 and T-8

    Tormek Drive Wheel with Rubber Band for T-7 and T-8

    Suitable for Tormek T-7, T-8 and old series models.
    €64.00

    incl. VAT plus shipping costs

    Article No. 800007

    Screw for Switch Hood Tormek

    Screw for Switch Hood Tormek

    Suitable for Tormek T-3, T-4, T-7, T-8 and old series models.
    €0.90

    incl. VAT plus shipping costs

    Article No. 800048

    Main Shaft Bearing for Tormek Supergrind 2000 / 1200

    Main Shaft Bearing for Tormek Supergrind 2000 / 1200

    Suitable for Tormek T-3, T-4, T-7, T-8 and old series models.
    €3.90

    incl. VAT plus shipping costs

    Article No. 800010

    Tormek Horizontal Base XB-100

    Tormek Horizontal Base XB-100

    For Tormek T-7 and T-3.
    €20.90

    incl. VAT plus shipping costs

    Article No. 705226

    Tormek Water Container WB-250

    Tormek Water Container WB-250

    Suitable for Tormek T-7 and old series models.
    €20.80

    incl. VAT plus shipping costs

    Article No. 705216

    Tormek Adjustable Cover for Rest

    Tormek Adjustable Cover for Rest

    Suitable for Tormek T-7 and old series models.
    €16.40

    incl. VAT plus shipping costs

    Article No. 800040

     

    You might also be interested in

    Customers also purchased

    Tormek Honing Compound PA-70

    €9.90

    (Content: €14.14 / 100 g)

    incl. VAT plus shipping costs

    Article No. 705213

    Customers also viewed

    Sharpening with the Tormek System

    €105.00

    incl. VAT Workshop No. KU4041732

    Micro-Gloss Polish

    €7.00

    (Content: €12.73 / 100 g)

    incl. VAT plus shipping costs

    Article No. 705482

    Sharpening with Grinding Machines

    €105.00

    incl. VAT Workshop No. KU4161702

    Sharpening with the Tormek System

    €105.00

    incl. VAT Workshop No. KU4041728

    Sharpening with the Tormek System

    €105.00

    incl. VAT Workshop No. KU4041724

    Viewed